PROGRAMMER TESTING CLIP SOP8 SOP SOIC 8 DIP8 DIP 8 PIN IC TEST CLAMP
Sangat kuat dan kokoh, pas di ic kecil soic 8pins
Rp47.500 Rp50.000
Produk Terkait
- Programmer Modul
UNO R3 SMD CH340 ATMEGA328P PLUS KABEL USB DAN PIN HEADER
0 out of 5(0)Spesifikasi :
– Microcontroller : ATmega328 SMD
– Operating Voltage : 5V
– Input Voltage (recommended) : 7-12V
– Digital I/O Pins : 14 (of which 6 provide PWM output)
– Analog Input Pins : 6
– Flash Memory : 32 KB (ATmega328) of which 0.5 KB used by bootloader
– SRAM : 2 KB (ATmega328)
– EEPROM : 1 KB (ATmega328)
– Clock Speed : 16 MHzSKU: ARD02Rp79.000Rp85.000 - Programmer Modul
ESP8266 ESP-13 WEB SERVER SERIAL WIFI SHIELD COMPATIBLE ARDUINO UNO
0 out of 5(0)FITUR
1. Modul WiFi berstandar industri dengan chip ESP8266, yaitu ESP-13 dan metal shield, memiliki kemampuan anti interferensi;
2. Kompatibel dengan Arduino Uno, Mega2560 dan board kontroler lain.
3. Sudah terdapat chip voltage converter di dalam shield yang menjembatani tegangan 3.3V dari ESP8266 menjadi 5V (arduino)
4. Terdapat 2 switch yang bisa memfungsikan modul sebagai shield ekspansi dari Arduino, atau juga ekspansi dari ESP8266.
5. Data serial dikirim ke perangkat WIFI secara langsung dan sebaliknya. Tidak memerlukan tambahan library program Arduino apapun.
6. Memiliki pengaturan parameter WiFi Web Server dan port serial berbasis web
7. Dapat digunakan sebagai sebuah development board ESP8266 independen.
8. Bisa digunakan juga sebagai “stand-alone expansion board” dari Arduino Uno.
9. Informasi selanjutnya http://www•doit•amSPESIFIKASI TEKNIS
1. 802.11 b / g / n wireless standards;
2. STA / AP modes support ;
3. TCP / IP protocol stack, One socket;
4. Supports standard TCP / UDP Server and Client;SKU: ARD18Rp180.000Rp195.000 - Programmer Modul
MICRO USB 5V 1A 18650 TP4056 LITHIUM BATTERY CHARGER MODULE CHARGING
0 out of 5(0)With MICRO USB female socket can be connect with mobile phone charger directly for charging lithium battery.
Input Voltage5V, Cut-off charging voltage 4.2V +/- 1%
Maximum charging current 1000mA
Battery over-discharge protection voltage 2.5V
Battery over-discharge protection current 3ANOTE:
1. Ampere meter can only be connected to 5v input end of the module.
2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to chip.
6. NO Reveral polarity.SKU: ARD19Rp7.900Rp9.000 - Programmer Modul
SOLENOID DOOR LOCK 12V DC – PENGUNCI PINTU ELEKTRIK
0 out of 5(0)Parameter:
– Tegangan: 12VDC
– Arus: 0.35A
– Ukuran: L:27mm*W:29mm*H:18mm
– Latch telescopic length: 10mm
– Energized forms: intermittent;
– Unlocking time: 1S
– continuously energized 10S ;Wiring:
Kabel Merah : Positive (+12VDC)
Kabel Hijau / Hitam: Negative (0V GND)SKU: ARD56Rp68.000Rp72.000