PARALEL 2X 18650 BATTERY HOLDER PLAT LEMPENGAN KOTAK BATERAI BATERE
Panjang : 7.8 cm
lebar : 4 cm
tinggi : 2.1 cm
Kelebihan:
– Bisa dijadikan PARALLEL maupun SERI
– Kontak dgn kutub batere memakai PLAT LEMPENGAN (bukan per/spring)
– Body plastik tebal dan solid, tidak bisa berubah bentuk
Rp11.000 Rp13.000
Produk Terkait
- Programmer Modul
SOLENOID DOOR LOCK 12V DC – PENGUNCI PINTU ELEKTRIK
0 out of 5(0)Parameter:
– Tegangan: 12VDC
– Arus: 0.35A
– Ukuran: L:27mm*W:29mm*H:18mm
– Latch telescopic length: 10mm
– Energized forms: intermittent;
– Unlocking time: 1S
– continuously energized 10S ;Wiring:
Kabel Merah : Positive (+12VDC)
Kabel Hijau / Hitam: Negative (0V GND)SKU: ARD56Rp68.000Rp72.000 - Programmer Modul
SOP8 TURN DIP8 SOIC8 TO DIP8 IC SOCKET PROGRAMMER ADAPTER SOCKET 150M
0 out of 5(0)Programmer(1.27 Pitch) and all SOP8 narrow chips.
Suitable for ALL-11 Series,ALL-100GANG , LT-48 Series, SuperPRO Series, TOP Series etc.
Support Chips: 24CXX, 93CXX and 25 Series all SOP8 narrow chips.SKU: ARD15Rp29.000Rp35.000 - Programmer Modul
MICRO USB 5V 1A 18650 TP4056 LITHIUM BATTERY CHARGER MODULE CHARGING
0 out of 5(0)With MICRO USB female socket can be connect with mobile phone charger directly for charging lithium battery.
Input Voltage5V, Cut-off charging voltage 4.2V +/- 1%
Maximum charging current 1000mA
Battery over-discharge protection voltage 2.5V
Battery over-discharge protection current 3ANOTE:
1. Ampere meter can only be connected to 5v input end of the module.
2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to chip.
6. NO Reveral polarity.SKU: ARD19Rp7.900Rp9.000 - Programmer Modul
NANO V3 ATMEGA168 CH340 COMPATIBLE FOR ARDUINO NANO V3.0
0 out of 5(0)It has similar structure with Arduino Diecimila/Duemilanove, but different size. To reduce the size, components are mounted on both sides of the PCB.
The board uses a chip CH340G as converter UART-USB. Chip CH340G – is a budget solution. With an operation frequency in 12Mhz, yields stable result of a data interchange (for correct installation of drivers on the computer follow the instruction). Nano V3, can be powered via microUSB-port (up to 500mA). External power supply 6-12V unregulated to output VIN, or 5V external power source to a regulate output of 5V. The power supply is automatically selected with the maximum voltage value.
* This Nano ATmega168 have PinOut for V3, not V2.Technical details:
Nano V3 form-factor,
ATmega168 (16Mhz) microcontroller,
CH340G – USB-UART interface,
Input voltage 6-12V,
Output voltage 5V/800mA, 3.3V/180mA (Only in NEW vesrion),
MicroUSB – connection socket,
500mA resetable Fuse on USB portSKU: ARD04Rp83.000Rp95.000