esp8266
Menampilkan semua 8 hasil
- IOT & ESP8266
ESP-12F (ESP-12E upgrade) ESP8266 remote serial WIFI wireless modul
Protocol 802.11 b/g/n
– Wi-Fi Direct (P2P), Soft-AP
– Integrated TR switch, Balun, LNA, Power Amplifier dan Matching Network
– Integrated TCP/IP protocol
– Integrated PLL, regulators, dan Power Management Unit
– Output power +19 dBm pada 802.11b mode
– Integrated temperature sensor
– Support antenna diversity
– Power down leakage : < 10uA
– Integrated low power 32-bit CPU, yang dapat digunakan sebagai processor aplikasi
– SDIO 2.0, SPI, UART
– STBC, 11 MIMO, 21 MIMO
– A-MPDU dan A-MSDU aggregation 0.4s interval
– Wake up dan Transmit packet dalam < 2ms
– Konsumsi daya standby < 1.0 mW (DTIM3)
– Ukuran board : 24 mm x 16 mm
– Tegangan kerja 3.3VSKU: IOT04 - LDC & Display
I2C IIC SERIAL INTERFACE BOARD MODULE FOR ARDUINO R3 LCD 1602 DISPLAY
Pemakaian Serial Interface IIC/I2C ini hanya diperlukan 2 port saja untuk mengendalikan LCD sehingga menghemat pemakaian port pada Arduino. Seperti contoh pada Arduino UNO, cukup hubungkan dengan pin A4/SDA dan A5/SCL selain pin +5V dan GND untuk power.
Kerjaan jadi simple dan praktis, hanya fokus pada 2 kabel saja SDA dan SCL.
**Spesifikasi:
1. Tegangan kerja: +5V
2. Mendukung protokol I2C, coding lebih singkat
3 Dilengkapi Trimpot pengatur lampu dan kontras layar
4. Hanya 4 pin utk pengendalian (SDA, SCL, VCC dan GND)
5. Device Address: 0x20
6. Ukuran: 41.5x19x15.3mm**Pengaturan kontras layar:
Putar trimpot searah jarum jam untuk meningkatkan kontras, putar ke arah sebaliknya untuk mengurangi kontras.**Datasheet:
http://www.arduiner.com/en/index.php?controller=attachment&id_attachment=173SKU: DISP02 - IOT & ESP8266
D1 MINI V1 – MINI NODEMCU 4M BYTES LUA WIFI IOT
Spesifikasi:
– 11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire supported(except D0)
– 1 analog input(3.3V max input)
– a Micro USB connection
– Compatible withArduino
– Compatible with nodemcu
– Auto Reset
– Header belum di solderKelengkapan:
1x WeMos D1 mini
2x Long female pins
2x Short female pins
2x Normal pinsSKU: IOT05 - IOT & ESP8266
ESP-01 ESP8266 SERIAL WIFI WIRELESS MODULE WIRELESS TRANSCEIVER
Upgraded Version ESP-01,all Flash are upgraded to 1M support loud service remote Upgraded Version module are fully supports the previous firmware.
The latest firmware version 1.0.1, the default baud rate of 115200, (AT + CIOBAUD = to change the baud rate), because the old version of the module is 512k bytes of storage space is not enough, so we can not upgrade the 1.0. 1 version, but also support the cloud services!Specifications:
– 802.11 b/g/n
– Wi-Fi Direct (P2P), soft-AP
– Integrated TCP/IP protocol stack
– Integrated TR switch, balun, LNA, power amplifier and matching network
– Integrated PLLs, regulators, DCXO and power management units
– +19.5dBm output power in 802.11b mode
– Power down leakage current of <10uA
– Integrated low power 32-bit CPU could be used as application processor
– SDIO 1.1/2.0, SPI, UART
– STBC, 1×1 MIMO, 2×1 MIMO
– A-MPDU & A-MSDU aggregation & 0.4ms guard interval
– Wake up and transmit packets in < 2ms
– Standby power consumption of < 1.0mW (DTIM3)Paket :
– 1x ESP8266 ESP-01E UPGRADED WIFI WIRELESS TRANSCEIVER MODULE 1MB FLASHSKU: IOT03 - Programmer Modul
ESP01 PROGRAMMER ADAPTER UART GPIO0 ESP-01
Product Description
This moduel is an USB adpater /
programmer for ESP8266 moduels of type ESP-01.
It is conveniently fitted with a 2x4P
2.54mm female header to plug the ESP01
(according to illustration picture 2)
and configure or run it right away.
A large 1000F cap will help getting a steady 5.0V VCC
from the USb bus and and jumper (on the right of the 2x4P header)
will help configuring the GPIO0 line according needs.
The module is based on the USB-UART bridget CH340
from WCH which is compatible with all platforms.SKU: ARD55 - Programmer Modul
ESP8266 ESP-13 WEB SERVER SERIAL WIFI SHIELD COMPATIBLE ARDUINO UNO
FITUR
1. Modul WiFi berstandar industri dengan chip ESP8266, yaitu ESP-13 dan metal shield, memiliki kemampuan anti interferensi;
2. Kompatibel dengan Arduino Uno, Mega2560 dan board kontroler lain.
3. Sudah terdapat chip voltage converter di dalam shield yang menjembatani tegangan 3.3V dari ESP8266 menjadi 5V (arduino)
4. Terdapat 2 switch yang bisa memfungsikan modul sebagai shield ekspansi dari Arduino, atau juga ekspansi dari ESP8266.
5. Data serial dikirim ke perangkat WIFI secara langsung dan sebaliknya. Tidak memerlukan tambahan library program Arduino apapun.
6. Memiliki pengaturan parameter WiFi Web Server dan port serial berbasis web
7. Dapat digunakan sebagai sebuah development board ESP8266 independen.
8. Bisa digunakan juga sebagai “stand-alone expansion board” dari Arduino Uno.
9. Informasi selanjutnya http://www•doit•amSPESIFIKASI TEKNIS
1. 802.11 b / g / n wireless standards;
2. STA / AP modes support ;
3. TCP / IP protocol stack, One socket;
4. Supports standard TCP / UDP Server and Client;SKU: ARD18 - IOT & ESP8266
NODEMCU ESP8266 CP2102 WIFI IOT LUA
Secara umum :
– Based ESP8266 Serial WiFi SoC dengan onboard USB to TTL menggunakan IC CP2102 (USB to UART Bridge Virtual COM Port)
– Bisa diprogram langsung lewat USB.
– Development Board dengan Open-Source Firmware ini dapat dipergunakan untuk mendevelop aplikasi IoT hanya dengan beberapa baris Lua script.
– Wireless standard : IEEE 802.11b/g/n
– 6 x Digital I/O, 3 x PWM Channels, 1 x ADC Channel
– Full I/O control through WiFi network
– GPIO with 15mA current drive capability
– Supports Smart Link intelligent networking
– Built in 32-bit MCU
– built-in TCP/IP protocol stack, and support multiple TCP Client connection
– UART/GPIO data communication interfaceSKU: n/a