arduino
Menampilkan 1–20 dari 108 hasil
- Programmer Modul
RASPBERRY PI CAMERA MODULE REV 1.3
Specification:
Sensor: Omnivision OV5647
Pixels Size: 5MP
Diagonal angle : 65 degree
Resolution: 2592 1944 still picture
Video Recording Support: 1080p30, 720p60 and 640x480p60/90
Compatibility: Raspberry Pi Standard Camera / CSI Port
Cable length: FFC 14 cm approxPackage Iist:
– 1 x Raspberry Pi Camera v1.3
– 1 x 14 cm FFC Flexible CableSKU: RAS03 - GSM & GPS
SIMCOM SIM800L V2.0 QUAD BAND GPRS GSM SMS MODULE 5V TTL ARDUINO PNP
Spesifikasi:
– TTL serial interface compatible with 3.3V and 5V Microcontrollers, compatible with arduino.
– This SIM800L module has a set of TTL level serial interface, a set of power supply interface.
– Besides, there are a set of antenna interface on this module.
– Network support: Quad-Band 850 / 900/ 1800 / 1900 MHz, it can transmit Voice, SMS and data information with low power
– VDD TTL UART interface The TTL UART serial interface, you can connect the MCU like 51MCU or ARM or MSP430 directly. The pin of VDD is used to match voltage of the TTL.
– Model: SIMCOM SIM800L
– Zunixe
– Work voltage: 3.7V to 5V
– Size: 40mm x 28mm x 3mm
– GPRS multi-slot class 12/10
– GPRS mobile station class B
– Compliant to GSM phase 2/2+
– Class 4 (2 W @ 850/900MHz)
– Class 1 (1 W @ 1800/1900MHz)Note : Imei produk ini belum didaftarkan, imei harus didaftarkan dulu di kemenperin atau bea cukai. tutorialnya bisa dicari di youtube.
Kelengkapan:
1 set SIM800L GSM/GPRS Module sudah termasuk dengan antenna externalnya dan kabel coaxial dengan panjang sekitar 10cmSKU: GSM07 - GSM & GPS
SIM808 GSM GPRS GPS MODULE BOARD ARDUINO RASPBERRY + ANTENNA
Spesifikasi:
– Quad-band 850/900/1800/1900MHz
– GPRS multi-slot class12
– connectivity: max. 85.6kbps(down-load/up-load)
– GPRS mobile station class B
– Controlled by AT Command (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT –
Commands)
– Supports Real Time Clock
– Supply voltage range 5V ~ 12V
– Integrated GPS/CNSS and supports A-GPS
– Supports 3.0V to 5.0V logic level
– Low power consumption, 1mA in sleep mode
– Supports GPS NMEA protocol
– Standard Micro SIM CardNote : Imei produk ini belum didaftarkan, imei harus didaftarkan dulu di kemenperin atau bea cukai. tutorialnya bisa dicari di youtube.
Paket:
– 1x SIM808 GSM GPRS GPS MODULE BOARD ARDUINO RASPBERRY + ANTENNATerima kasih sudah mengunjungi halaman produk kami.
SKU: GSM03 - GSM & GPS
MODUL GPS UBLOX NEO 6MV2 U-BLOX NEO-6M UNTUK ARDUINO, RASPBERRY
Spesifikasi:
– Standalone GPS receiver
– 9600 baud (default setting; can be changed)
– VCC = 3,3V
– Serial TTL 3V3 (PIN IO harus menggunakan resistor pembagi tegangan atau TTL converter untuk koneksi ke Arduino, lihat foto)
– Onboard LED which flashes to indicate lock
– U-blox NEO-6M GPS module
– Under 1 second time-to-first-fix for hot and aided starts
– Indoor GPS: -162 dBm tracking sensitivity
– Anti-jamming technology
– Support SBAS (WAAS, EGNOS, MSAS, GAGAN)
– U-blox 6 50 channel positioning engine with over 2 million effective correlators
– Timepulse
– 5Hz position update rate
– Operating temperature range: -40 TO 85C
– UART TTL socket
– Visit zunixe dot com
– EEprom to store settingsPaket:
1pcs GPS Module NEO 6MV2
1pcs GPS Antenna dengan IPX Connector (Antenna dapat disolder ke belakang PCB module GPS)SKU: n/a - Programmer Modul
RFID STARTER KIT FOR ARDUINO UNO R3 UPGRADED VERSION – TERBARU
RFID Learning Suite is the entry to the master suite upgrades, updates place mainly in:
1.1602 I2C 1602 replaced the screen to control it more convenient,
2•New RFID module and RFID keychain and white card,
3. Added DS1302 clock module,
4. New of the sound detection module,
5•New temperature and humidity module,
6. New water level detection module,
7. Added 4 * 4 keypad module
8. New of 8 * 8 dot matrix modulePackage Included:
1 X UNO Board
1 X USB Cable
1 X Jump Cable
1 X Breadboard
5 X LED Light
1 Pack Resistor
1 X Female to male dupond line
1 X Potentiometer
1 X Buzzer
1 X 74HC595
1 X Infrared receiver
1 X LM35
1 X Flame Sensor
1 X Ball Switch
1 X Photoresistor
1 X Key button
1 X Remote control
1 X 4-digit display tube
1 X 8*8 Dot matrix module
1 X 1-digit display tube
1 X Stepper motor driver board
1 X Stepper motor
1 X 9g Servo
1 X IIC 1602 LCD
1 X XY joystick module
1 X Temperature module
1 X Water test module
1 X RFID Module
1 X RFID keychain
1 X RFID White card
1 X Sound Module
1 X Relay Module
1 X Clock Module
1 X 4*4 Key board
1 X RGB 3 color module
1 X 9V battery SnapSKU: TOOL06 - Programmer Modul
MINI DIGITAL MULTIMETER DC AC VOLTAGE CURRENT TESTER PEAKMETER MS8232
The instrument can measure DC voltage, AC voltage, DC current, AC current, resistance, diode and connectivity; with non-contact voltage detection function, timely remind the user to pay attention to operation safety, so it’s more safe and rest assured for user to use.
Powered by 2 x AAA battery ( not included )
Brand: PEAKMETER
Model: MS8232
Material: ABS
Type: Measuring instruments
Professional instruments: Multimeter
Primary functions: Non-contact AC DC voltage, current and impedance measurement
Scope of application: Agricultural,Home appliance,IndustrialIsi Paket:
1x MINI DIGITAL MULTIMETER DC AC VOLTAGE CURRENT TESTER PEAKMETER MS8232′SKU: TOOL02 - Programmer Modul
NTAG215 NFC FORUM TYPE 2 TAG ISO/IEC SMART CARD 14443 A NFC CARDS TAG
Spesifikasi :
Product specifications
Cards size : 85.6*54*0.8mm
Cards Material : PVCElectronic specifications
Chip Type : NTAG215
Protocol : ISO/IEC 14443 A
Operating frequency : 13.56 MHz
NFC Forum Type : NFC Forum Type 2 Tag
Lockable : YES
Reading distance : 0-10cm
Memory : 540 Bytes
Usable Memory : 504 Bytes
Write endurance : > 100000 cycles
Data Retention : > 10 Years
Quality : 100% testEnvironment
Operating temperature : -25 °C to 70 °C
Storage temperature : -55 °C to 125 °CIsi Paket :
1x NTAG215 NFC FORUM TYPE 2 TAG ISO/IEC SMART CARD 14443 A NFC CARDS TAGSKU: NFC06 - Programmer Modul
SIM900A V4.0 KIT WIRELESS EXTENSION MODULE GSM GPRS
Fitur:
– Power supply oleh 5V , dapat didukung oleh USB , untuk penggunaan jangka panjang lebih baik menggunakan power supply 1A tersendiri dengan konektor XH2.54-2P .
– TTL 5V dan 3V3 ( pin kuning ditandai on board) , yang kompatibel dengan Arduino , STM32 , raspberry pi , dll
– Onboard RS232 yang memudahkan untuk debugging . Di sebelah kiri , pin putih .
– Pada papan ada LED sinyal di kiri – atas sudut IC SIM900A.
On Board ulang dan restart pin , pada bagian bawah SIM900A IC .
– Meiiliki konektor Mini IPX , tetapi belum disolder .
– Standar konektor antena SMA .
– Serial port dilindungi oleh TVS untuk mencegah lonjakan arus atau HV .
– Sirkuit SIM memiliki elektrostatika SMF05C melepaskan IC .
– Paket termasuk antena dan DC jack.
– Ukuran Module : 49mm x 47mmNote : Imei produk ini belum didaftarkan, imei harus didaftarkan dulu di kemenperin atau bea cukai. tutorialnya bisa dicari di youtube.
SKU: NFC05 - Programmer Modul
PN532 NFC PRECISE RFID IC CARD READER MODULE 13.56MHZ FOR RASPBERRY PI
Characteristics
The longest effective communication distance is 5 cm
Support SPI, IIC, UART interface switching.
Can be used for 13.56M contactless communication
Compatible with ISO14443 TYPE A and Class B standardsspecification
chip NXP PN532
Operating Voltage 3.3V
voltage 3.3 to 5.5V
Maximum supply current 150 mAh
Working current (standby mode) 100 mAh
Working current (write mode) 120 mAh
Working current (read mode) 120 mAh
pointer PWR
interface Raspberry Pi’s 20pins interface standard SPI interface,There are two slide switches on the board to select the interface mode:
SET0 SET1
UART L L
SPI L H
IIC H LIsi Paket
1x PN532 NFC PRECISE RFID IC CARD READER MODULE 13.56MHZ FOR RASPBERRY PISKU: NFC04 - Programmer Modul
13.56 MHZ MIFARE MFRC-522 RC522 RFID READER WRITER ARDUINO
Tinggal solder sedikit dan download library, sudah bisa bereksperimen.
Salah satu library bisa di download di https://github•com/miguelbalboa/rfidSpesifikasi:
Operating current :13-26mA/DC 3.3V
Idle current :10-13mA/DC 3.3V
Sleep current: 80uA
Peak current: 30mA
Operating Frequency: 13.56MHz
Supported card types: mifare1 S50, mifare1 S70 MIFARE Ultralight, mifare Pro, MIFARE DESFire
Product physical characteristics: size: 40mm60mm
Environmental Operating temperature: -20-80 degrees Celsius
Environmental Storage Temperature: -40-85 degrees Celsius
Relative humidity: relative humidity 5% -95%
Module interfaces SPI Parameter:
Data transfer rate: maximum 10Mbit/sSKU: NFC02 - Programmer Modul
PN532 NFC RFID MODULE V3 ARDUINO
Spesifikasi:
– Small dimension
– Support I2C, SPI and HSU (High Speed UART)
– Support RFID reading and writing, P2P communication with peers, NFC with Android phone
– RFID reader/writer supports (Mifare 1k, 4k, Ultralight, and DesFire cards, ISO/IEC 14443-4 cards such as CD97BX, CD light, Desfire, P5CN072)
– Up to 5cm~7cm reading distance
– On-board level shifter, Standard 5V TTL for I2C and UART, 3.3V TTL SPI
– Arduino compatibleIsi Paket:
– 1Unit PN532 NFC RFID Module
– 1pc 2.54mm spacing 4pin Cable
– 1pc Mifare One S50 White Card
– 1pc Mifare One S50 Key Card
– 4pcs Jumper Cable M-MSKU: NFC01 - Programmer Modul
NEMA 17 STEPPER MOTOR 4-LEAD 17HS4401 1.7A 2 PHASE 42 MOTOR UNTUK CNC
Electrical Specification:
Motor Type: Bipolar Stepper
Step Angle: 1.8 deg.
Holding Torque: 40N.cm (56oz.in)
Rated Current/phase: 1.7A
Phase Resistance: 1.5Ohm±10%
Insulation Resistance: 100MΩ¸ Min, 500VDC
Insulation Strength: 500VAC for one minute
Physical Specification:Frame Size: 42 x 42mm (1.7 inch x 1.7 inch)
Body Length: 40mm
Shaft Diameter: 5mm
Number of Wire Leads: 4
Wire Length: 400mm
Weight: 280g
Temperature rise: 80deg Max(rated current, 2 phase on)Bisa digunakan untuk 3d printer prusa i3
Mesin CNC Router / EngravingSKU: CNC01 - DC-DC Step Up/Down & Charger
DC POWER SUPPLY MODULE FOR DC POWER ADAPTER PLATE
1 name: DC power adapter plate
2 size: 2.8cm*1.3cm
3 applicable connector: 5.5*2.1mm
4 Reserve 2 single 4 pin hole, fitted directly on the hole Board to facilitate testing
5 power supply output connector: 2-way VCC,2 road, GNDSKU: STEP07