Relay & Driver Motor
Menampilkan semua 18 hasil
- Relay & Driver Motor
TDR MODULE 6-30V RELAY MODULE SWITCH TRIGGER TIME DELAY CIRCUIT
Memiliki Fitur Sbb :
Terdapat konektor Micro USB selain itu
Peralatan kontrol ini dapat dikombinasikan dengan peralatan kontrol lain, contohnya dengan MC (Magnetic Contactor), Thermal Over Load Relay, dan lain-lain.
misalnya untuk rangkaian control hubungan motor secara otomatis, hubungan control secara berurutan dan lain lain.Spesifikasi :
– 100% baru dan bermutu tinggi
– Operating voltage: 6–30VDC
– Trigger Signal Source : High Level Trigger (3.0 V-24 V), signal ground and system ground are not common, which can increase anti-interference abilit
system (short circuit can also connect with a ground common)
– Output Capacity : can control no more than DC 30V 5A AC or 220 V devices 5A
– Optocoupler Isolation : improve the anti-interference ability, after the parameter setting, it will memory forever
Warning: Relay contact is passive and electricity production; 1 channel has the control function on / offCara setting:
P1: After triggered signal, power relay on time OP, then turn off; within the OP period following operation:
1) P1.1: signal being triggered again is not effective
2) P1.2: signal being triggered again, start time again
3) P1.3: signal being triggered again, reset; disconnect relay, stop timing
P2: giving the trigger signal, the time after shutdown relay CL power relay OP time; then timing, turn off the relayTersedia Warna
– Dengan PCB BiruUkuran :
P x L x T : 6.3 * 3.8 * 1.5cmKelengkapan :
– 1Pc x TDR Module Time Delay Relay C90A 6-30V DCSKU: MOT18 - Relay & Driver Motor
Modul Relay 1 Channel 12V Arduino
MODULE INTERFACE
Input part :
VCC : Connect to power positive (according to the relay voltage range)
GND : Connect to power negative
IN : Relay module trigger pin (low level trigger)Output part :
Normally Opened (NO) : Normally open pin of relay. NO pin is not connect to COM pin when relay off. NO pin is connect to COM pin when relay on
Common pin (COM) : Common pin of the relay
Normally closed (NC) : Normally close pin of relay. NC pin is connect to COM pin when relay off. NC pin is not connect to COM pin when relay onElectrical parameters :
– Voltage version : 12V
– The static current : 4mA
– Working current : 65mA
– Trigger voltage : 10-12V
– Trigger current : 2mASKU: MOT17 - Relay & Driver Motor
N20 DIRECT CURRENT MOTOR HIGH-SPEED AERO-MODE MOTOR 1.5-4 .5 V
Spesifikasi:
Motor specification: 10 * 12 * 14.6 MM
Output shaft: 1 MM
Output shaft length: 5MM
Voltage: 1.5-4.5 V
1.5 V current 0.3 A rpm 16,000 rpm
3V current 0.5 A rpm 32000 revolutions
3.7 V Current 0.6 A Rpm 39500
The distance between the two screw holes is 9mm.SKU: MOT16 - Relay & Driver Motor
MG995 55G SERVOS DIGITAL METAL GEAR RC CAR ROBOT SERVO
Dimension : 40mm x 19mm x 43mm
Net weight: 69g
Package weight: 75g
Color: Black
Operating Speed : 0.17sec / 60 degrees (4.8V no load)
Operating Speed : 0.13sec / 60 degrees (6.0V no load)
Stall Torque : 13 kg-cm (180.5 oz-in) at 4.8V
Stall Torque : 15 kg-cm (208.3 oz-in) at 6V
Operation Voltage : 2Volts
Gear Type: All Metal Gears
Connector Wire: Heavy Duty, 300mm)Paket :
1. 1x TOWERPRO MG995 SERVO MOTOR 55GSKU: MOT15 - Relay & Driver Motor
Metal Servo ARm 25T Remote Control Rc Metal Servo Arm Lengan 25T Steering – Merah
-23%Relay & Driver MotorMetal Servo ARm 25T Remote Control Rc Metal Servo Arm Lengan 25T Steering – Merah
Features:
Color: Red
Material: Aluminum
Hole centers at 20 and 24mm from the servo output
25T spine for Futaba and power HD servos
Adjustable type servo arm
25T spine for Futaba and power HD servos
Includes two steel bolts to secure the split-clamp onto the servo output
M3 threads for your car or helicopter jointsIsi Paket :
1 x Metal Servo ARm 25T Remote Control Rc Metal Servo Arm Lengan 25T Steering – MerahSKU: MOT12 - Relay & Driver Motor
SMART WHEEL DC MOTOR + GEAR BOX 1:48 RODA ROBOT
**Fitur:
1. Bekerja pada tegangan 3-6v DC.
2. Dapat digunakan untuk platform robotik, robot line-tracing, dan banyak lagi.
3. Dengan rasio 1:48 akan didapatkan torgue dan rpm yang baik sehingga cukup kuat untuk tanjakan dan karpet.
4. Dapat dipasang roda pada kedua sisinya.**Spesifikasi:
Tegangan kerja: 3-6v (rekomendasi 5v)
Rasio kecepatan tanpa beban: 1:48 (saat 3v)
Torsi max: 0.8 kgcm
Kecepatan (meter/menit): 3v (26), 5v (44)
Ukuran motor dan gearbox: 70x22x18mm
Ukuran roda dan ban: diameter 66mm x 25mmSKU: MOT11 - Relay & Driver Motor
L293D MOTOR DRIVER SHIELD ARDUINO
Spesifikasi :
-Four H-Bridges: Two L293D Motor driver chips
-L293D is rated at 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
-Motor Voltages from 4.5VDC to 16VDC. (up to 36V if C6 and C7 are upgraded)
-Up to 4 bi-directional DC motors with individual 8-bit speed selection (256 speeds)
-Up to 2 stepper motors (unipolar or bipolar)
-Pull down resistors keep motors disabled during power-up
-Separate Logic and Motor power connections
-Terminal block connectors for motors and power
-2 connections for 5V ‘hobby’ servosDimensi (PxLxT) : 7 x 5.3 x 1.3 cm
SKU: MOT10 - Relay & Driver Motor
RELAY 5V 1 CHANNEL ACTIVE HIGH / ACTIVE LOW
Spesifikasi:
Active high 5V 1-Channel Relay interface board, arus sink 15 mA – bisa langsung dari pin mikrokontroler;
Kapasitas relay, AC250V 10A ; DC30V 10A;
Interface standard TTL logic langsung dikendalikan mikrokontroler (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)
Rangkaian proteksi (arus kickback) sudah termasuk di dalamnya – aman dan siap digunakan
LED indikator untuk menandakan channel yang aktifIsi Paket :
1x RELAY 5V 1 CHANNEL ACTIVE HIGHSKU: MOT09 - Relay & Driver Motor
RELAY MODUL 8 CHANNEL 5V FOR ARDUINO
Spesifikasi:
– 5V 8-Channel Relay interface board, arus sink 15 mA – bisa langsung dari pin mikrokontroler;
– Kapasitas relay, AC250V 10A ; DC30V 10A;
– Interface standard TTL logic langsung dikendalikan mikrokontroler (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)
– Rangkaian proteksi (isolasi, arus kickback) sudah termasuk di dalamnya – aman dan siap digunakan
– LED indikator untuk menandakan channel yang aktifSKU: MOT08 - Relay & Driver Motor
MG996R MICRO SERVO MG996 METAL HIGH TORQUE ARDUINO
Untuk masalah torsi atau kekuatan gk perlu diragukan lagi, ini sangat kuat hingga 10Kg.
Jadi tunggu apalagi gan, silahkan di order 😀
Kelebihan:
– MG996R adalah versi peningkatan dari MG995R, revisi PCB, positioning lebih akurat dan unit tahan banting
– gear berbahan kuningan, double bearing, kuat, stabil dan shock proof
– Cocok sekali untuk Truck, Boat, Racing Car, Helicopter dan Airplane
– Compliant dengan semua standar connector receiver: Futaba, Hitec, Sanwa, GWS etcSpecifications:
– Weight: 55 g
– Dimension: 40.7 x 19.7 x 42.9 mm approx.
– Gear Type: Tidak full metal gear
– Stall torque: 9.4 kgfcm (4.8 V ), 11 kgfcm (6 V)
– Degree: max 180 degrees servo rotation
– Operating speed: 0.17 s/60 (4.8 V), 0.14 s/60 (6 V)
– Operating voltage: 4.8 V a 7.2 V
– Running Current 500 mA – 900 mA (6V)
– Stall Current 2.5 A (6V)
– Dead band width: 5us
– Stable and shock proof double ball bearing design
– Temperature range: 0C – 55CPaket :
1. 1x Servo Motor TowerPro MG996R 180°
2. 1x set accesoriesSKU: MOT01 - Relay & Driver Motor
Motor Driver L298N Board Modul Arduino
Detail Produk:
++ Double H bridge drive
++ Chip: L298N (ST NEW)
++ Logical voltage: 5V
++ Drive voltage: 5V-35V
++ Logical current: 0mA-36mA
++ Drive current: 2A(MAX single bridge)
++ Max power: 25W
++ Size:43 x 43 x 26mm
++ Net weight: 26g
++ Package weight:36gSKU: MOT03 - Relay & Driver Motor
SG90 9G MINI MICRO SERVO MOTOR 9GRAM
Specifications:
– Weight: 9g
– Dimension: 22mm x 11.5mm x 22.5mm
– Stall torque: 1.8kg/cm(4.8v)
– Gear type: POM gear set
– Operating speed: 0.1sec/60degree(4.8v)
– Operating voltage: 4.8v
– Temperature range: 0_ 55
– Dead band width: 1us
– Power Supply: Through External Adapter
– servo wire length: 25 cmSKU: MOT06 - Relay & Driver Motor
MG90S MICRO MOTOR SERVO TOWER PRO, HIGH SPEED 9G
spesifikasi:
Dimension: 22.8mm x 12.2mm x 28.5mm
Degree: max 180
Stall torque: 1.8kg/cm(4.8V )2.2kg/cm(6V)
Operating speed: 0.1sec/60degree(4.8v), 0.08sec/60degree(6v)
Operating voltage: 4.8-6.0V
Dead band width: 5us
Analog ModulationSKU: MOT04 - Relay & Driver Motor
Smart robot car chassis kit speed encoder battery box 2wd for arduino
Frame kondisi belum dirakit butuh proses perakitan
Isi Paket
– 1x Chassis Acrylic with 4mm thickness
– 2x 3-6V DC Motor Gearbox
– 2x Strong alumunium bracket motor with screw
– 2x Roda
– 1x Metal Ball Caster
– 1x Battery Holder
– 1x On/Off Switch
– Baut dan Mur LengkapSKU: MOT02