Tidak ada produk di keranjang.
Product Carousel Tabs
Programmer Modul
MICRO USB 5V 1A 18650 TP4056 LITHIUM BATTERY CHARGER MODULE CHARGING
1. Charge module- Linear charging.
2. Current- 1A adjustable.
3. Charge precision- 1.5%.
4. Input voltage- 4.5V-5.5V.
5. Full charge voltage- 4.2V.
6. Led indicator- red is charging Green is full charged.
7. Input interface- micro USB.
8. Work temperature- -10 to +85.
9. Inversed polarity- NO.
10.Size- small about 26mm x 17mm
With MICRO USB female socket can be connect with mobile phone charger directly for charging lithium battery.
Input Voltage5V, Cut-off charging voltage 4.2V +/- 1%
Maximum charging current 1000mA
Battery over-discharge protection voltage 2.5V
Battery over-discharge protection current 3A
NOTE:
1. Ampere meter can only be connected to 5v input end of the module.
2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to chip.
6. NO Reveral polarity.
SKU: ARD25
IOT & ESP8266
ESP32 ESP-32 ESP-32S DEVELOPMENT BOARD WIFI BLUETOOTH IOT
Features:
=================================
– High performance-price ratio;
– Small volume,easily embeded to other products;
– Strong function with support LWIP protocol,Freertos;
– Suppporting three modes: AP, STA, and AP+STA;
– Supporting Lua program, easily to develop.
Spesifikasi:
=================================
– Operating voltage : 3.3V
– Input voltage : 7-12V (Vin)
– Digital IO Pin (DIO) : 25
– Analog Input Pin (ADC) : 6
– Analog Output Pin (DAC) : 2
– UART : 3
– SPI : 2
– I2C : 3
– Flash Memory 4 MB
– SRAM : 520 KB
– Clock Speed : 240 Mhz
– Wi Fi : IEEE 802.11 b/g/n/e/i
– Mode supported : AP, STA, AP+STA
– CP2102 USB ccontroller
Aplikasi:
=================================
– IOT
– Smart lighting
– Wireless sensor networks
– Home automation
– Tele medicine
– Telemetri
– WiFi / Bluetooth Audio player
– WiFi camera
– MP3 decoding
– WiFi range extender
SKU: IOT11
IOT & ESP8266
CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32
Features:
– Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
– Low-power dual-core 32-bit CPU for application processors
– Up to 240MHz, up to 600 DMIPS
– Built-in 520 KB SRAM, external 4M PSRAM
– Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
– Support OV2640 and OV7670 cameras with built-in flash
– Support for images WiFI upload
-Support TF card
– Support multiple sleep modes
– Embedded Lwip and FreeRTOS
– Support STA/AP/STA+AP working mode
– Support Smart Config/AirKiss One-click distribution network
– Support for serial local upgrade and remote firmware upgrade (FOTA)
Note:
This product contains the OV2640 Camera Module. If you need to use the OV7670 camera, please purchase it separately.
Paket :
1 x CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32
SKU: IOT10
Power Amplifier
Power Amplifier Board TPA3116D2 XH-M548 Bluetooth
XH-M548 Bluetooth Dual Channel 120W+120W TPA3116D2 Digital Audio Power Amplifier Board Module
Specification:
Chip: TPA31 16D2
Power supply voltage: DC12 to 24V
Output power: 120W x 2
Power supply current: > 3A
Power ratio: >90%
Bluetooth module: BTM835/CRS8635 (4.0 edition)
Transmission distance: maximum 10m (no interference)
Channel number: 2 channel (high bass control)
Switching frequency: 1.2MHz
Support system: for Android IOS Windows
Size: 98 x 80 x 15mm/3.85 x 3.14 x 0.59”
Bluetooth connection method:
Take mobile phones as an example:
1. Turn on the Bluetooth.
2. Turn on “check all your devices around you”.
3. Click the search device “loudspeaker”, and connected.
4. The Bluetooth status indicator does not flicker alternately, turn on the player and listen to the music.
Isi paket :
1x Power Amplifier Board TPA3116D2 XH-M548 Bluetooth
SKU: AMP01
Programmer Modul
RASPBERRY PI CAMERA MODULE REV 1.3
Specification:
Sensor: Omnivision OV5647
Pixels Size: 5MP
Diagonal angle : 65 degree
Resolution: 2592 1944 still picture
Video Recording Support: 1080p30, 720p60 and 640x480p60/90
Compatibility: Raspberry Pi Standard Camera / CSI Port
Cable length: FFC 14 cm approx
Package Iist:
– 1 x Raspberry Pi Camera v1.3
– 1 x 14 cm FFC Flexible Cable
SKU: RAS03
Led
3 Digit LED Seven Segment 7 segmen 0.56″ inch Red Common Cathode Merah
Jumlah kaki : 12 pin
Tinggi angka : 0.56inch / 14.3mm
Ukuran display :
P : 37.5MM
L : 19mm
T: 8mm
Warna : Merah
Jumlah digit : 3 angka
Jenis Kolon : Titik
Jenis Segment : Common Cathode (Pin GND (-) jadi satu)
Tegangan Kerja : 2.8 – 5.0V DC (rekomendasi 2.8-3.3v kalau ke 5V bisa menggunakan R 100-220 Ohm. Tanpa Resistor berpotensi tidak tahan lama terutama bagian dot)
SKU: DISP05
Programmer Modul
MICRO USB 5V 1A 18650 TP4056 LITHIUM BATTERY CHARGER MODULE CHARGING
1. Charge module- Linear charging.
2. Current- 1A adjustable.
3. Charge precision- 1.5%.
4. Input voltage- 4.5V-5.5V.
5. Full charge voltage- 4.2V.
6. Led indicator- red is charging Green is full charged.
7. Input interface- micro USB.
8. Work temperature- -10 to +85.
9. Inversed polarity- NO.
10.Size- small about 26mm x 17mm
With MICRO USB female socket can be connect with mobile phone charger directly for charging lithium battery.
Input Voltage5V, Cut-off charging voltage 4.2V +/- 1%
Maximum charging current 1000mA
Battery over-discharge protection voltage 2.5V
Battery over-discharge protection current 3A
NOTE:
1. Ampere meter can only be connected to 5v input end of the module.
2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to chip.
6. NO Reveral polarity.
SKU: ARD25
IOT & ESP8266
ESP32 ESP-32 ESP-32S DEVELOPMENT BOARD WIFI BLUETOOTH IOT
Features:
=================================
– High performance-price ratio;
– Small volume,easily embeded to other products;
– Strong function with support LWIP protocol,Freertos;
– Suppporting three modes: AP, STA, and AP+STA;
– Supporting Lua program, easily to develop.
Spesifikasi:
=================================
– Operating voltage : 3.3V
– Input voltage : 7-12V (Vin)
– Digital IO Pin (DIO) : 25
– Analog Input Pin (ADC) : 6
– Analog Output Pin (DAC) : 2
– UART : 3
– SPI : 2
– I2C : 3
– Flash Memory 4 MB
– SRAM : 520 KB
– Clock Speed : 240 Mhz
– Wi Fi : IEEE 802.11 b/g/n/e/i
– Mode supported : AP, STA, AP+STA
– CP2102 USB ccontroller
Aplikasi:
=================================
– IOT
– Smart lighting
– Wireless sensor networks
– Home automation
– Tele medicine
– Telemetri
– WiFi / Bluetooth Audio player
– WiFi camera
– MP3 decoding
– WiFi range extender
SKU: IOT11
IOT & ESP8266
CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32
Features:
– Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
– Low-power dual-core 32-bit CPU for application processors
– Up to 240MHz, up to 600 DMIPS
– Built-in 520 KB SRAM, external 4M PSRAM
– Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
– Support OV2640 and OV7670 cameras with built-in flash
– Support for images WiFI upload
-Support TF card
– Support multiple sleep modes
– Embedded Lwip and FreeRTOS
– Support STA/AP/STA+AP working mode
– Support Smart Config/AirKiss One-click distribution network
– Support for serial local upgrade and remote firmware upgrade (FOTA)
Note:
This product contains the OV2640 Camera Module. If you need to use the OV7670 camera, please purchase it separately.
Paket :
1 x CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32
SKU: IOT10
Power Amplifier
Power Amplifier Board TPA3116D2 XH-M548 Bluetooth
XH-M548 Bluetooth Dual Channel 120W+120W TPA3116D2 Digital Audio Power Amplifier Board Module
Specification:
Chip: TPA31 16D2
Power supply voltage: DC12 to 24V
Output power: 120W x 2
Power supply current: > 3A
Power ratio: >90%
Bluetooth module: BTM835/CRS8635 (4.0 edition)
Transmission distance: maximum 10m (no interference)
Channel number: 2 channel (high bass control)
Switching frequency: 1.2MHz
Support system: for Android IOS Windows
Size: 98 x 80 x 15mm/3.85 x 3.14 x 0.59”
Bluetooth connection method:
Take mobile phones as an example:
1. Turn on the Bluetooth.
2. Turn on “check all your devices around you”.
3. Click the search device “loudspeaker”, and connected.
4. The Bluetooth status indicator does not flicker alternately, turn on the player and listen to the music.
Isi paket :
1x Power Amplifier Board TPA3116D2 XH-M548 Bluetooth
SKU: AMP01
Programmer Modul
RASPBERRY PI CAMERA MODULE REV 1.3
Specification:
Sensor: Omnivision OV5647
Pixels Size: 5MP
Diagonal angle : 65 degree
Resolution: 2592 1944 still picture
Video Recording Support: 1080p30, 720p60 and 640x480p60/90
Compatibility: Raspberry Pi Standard Camera / CSI Port
Cable length: FFC 14 cm approx
Package Iist:
– 1 x Raspberry Pi Camera v1.3
– 1 x 14 cm FFC Flexible Cable
SKU: RAS03
Led
3 Digit LED Seven Segment 7 segmen 0.56″ inch Red Common Cathode Merah
Jumlah kaki : 12 pin
Tinggi angka : 0.56inch / 14.3mm
Ukuran display :
P : 37.5MM
L : 19mm
T: 8mm
Warna : Merah
Jumlah digit : 3 angka
Jenis Kolon : Titik
Jenis Segment : Common Cathode (Pin GND (-) jadi satu)
Tegangan Kerja : 2.8 – 5.0V DC (rekomendasi 2.8-3.3v kalau ke 5V bisa menggunakan R 100-220 Ohm. Tanpa Resistor berpotensi tidak tahan lama terutama bagian dot)
SKU: DISP05
Programmer Modul
RASPBERRY PI NOIR CAMERA MODULE V2 8MP PIXELS 1080P
Item description:
— NoIR camera,the Infrared night vision Camera V2
–800MP pixels, up to 3280 x 2464 pixels static image
–Support 1080p30, 720p60 and 640x480p60 / 90 camera shooting
–Latest Sony IMX219 sensor
Raspberry Pi Official Original NoIR Camera v2,The lastest IMX219 sensor,8 megapixel,The Infrared night vision Camera V2
Package Included:
Official Raspberry Pi Camera V2 Night Vision * 1
Note:(Raspberry Pi Board is not included)
SKU: RAS02
GSM & GPS
SIMCOM SIM800L V2.0 QUAD BAND GPRS GSM SMS MODULE 5V TTL ARDUINO PNP
Spesifikasi:
– TTL serial interface compatible with 3.3V and 5V Microcontrollers, compatible with arduino.
– This SIM800L module has a set of TTL level serial interface, a set of power supply interface.
– Besides, there are a set of antenna interface on this module.
– Network support: Quad-Band 850 / 900/ 1800 / 1900 MHz, it can transmit Voice, SMS and data information with low power
– VDD TTL UART interface The TTL UART serial interface, you can connect the MCU like 51MCU or ARM or MSP430 directly. The pin of VDD is used to match voltage of the TTL.
– Model: SIMCOM SIM800L
– Zunixe
– Work voltage: 3.7V to 5V
– Size: 40mm x 28mm x 3mm
– GPRS multi-slot class 12/10
– GPRS mobile station class B
– Compliant to GSM phase 2/2+
– Class 4 (2 W @ 850/900MHz)
– Class 1 (1 W @ 1800/1900MHz)
Note : Imei produk ini belum didaftarkan, imei harus didaftarkan dulu di kemenperin atau bea cukai. tutorialnya bisa dicari di youtube.
Kelengkapan:
1 set SIM800L GSM/GPRS Module sudah termasuk dengan antenna externalnya dan kabel coaxial dengan panjang sekitar 10cm
SKU: GSM07
GSM & GPS
SIM900 GSM GPRS QUAD BAND SHIELD MODULE FOR ARDUINO UNO MEGA
Features
Quad-Band 850 / 900/ 1800 / 1900 MHz – would work on GSM networks in all countries across the world.
GPRS multi-slot class 10/8
GPRS mobile station class B
Compliant to GSM phase 2/2+
Class 4 (2 W @ 850 / 900 MHz)
Class 1 (1 W @ 1800 / 1900MHz)
Control via AT commands – Standard Commands: GSM 07.07 & 07.05 |
Enhanced Commands: SIMCOM AT Commands.
Short Message Service – so that you can send small amounts of data over the network
(ASCII or raw hexadecimal).
Embedded TCP/UDP stack – allows you to upload data to a web server.
RTC supported.
Selectable serial port.
Speaker and Headphone jacks
Low power consumption – 1.5mA(sleep mode)
Industrial Temperature Range – -40°C to +85 °C
Size:8.5×5.7x2cm(approx)
Note : Imei produk ini belum didaftarkan, imei harus didaftarkan dulu di kemenperin atau bea cukai. tutorialnya bisa dicari di youtube.
SKU: GSM06
GSM & GPS
SIM808 GSM GPRS GPS MODULE BOARD ARDUINO RASPBERRY + ANTENNA
Spesifikasi:
– Quad-band 850/900/1800/1900MHz
– GPRS multi-slot class12
– connectivity: max. 85.6kbps(down-load/up-load)
– GPRS mobile station class B
– Controlled by AT Command (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT –
Commands)
– Supports Real Time Clock
– Supply voltage range 5V ~ 12V
– Integrated GPS/CNSS and supports A-GPS
– Supports 3.0V to 5.0V logic level
– Low power consumption, 1mA in sleep mode
– Supports GPS NMEA protocol
– Standard Micro SIM Card
Note : Imei produk ini belum didaftarkan, imei harus didaftarkan dulu di kemenperin atau bea cukai. tutorialnya bisa dicari di youtube.
Paket:
– 1x SIM808 GSM GPRS GPS MODULE BOARD ARDUINO RASPBERRY + ANTENNA
Terima kasih sudah mengunjungi halaman produk kami.
SKU: GSM03
Programmer Modul
MICRO USB 5V 1A 18650 TP4056 LITHIUM BATTERY CHARGER MODULE CHARGING
1. Charge module- Linear charging.
2. Current- 1A adjustable.
3. Charge precision- 1.5%.
4. Input voltage- 4.5V-5.5V.
5. Full charge voltage- 4.2V.
6. Led indicator- red is charging Green is full charged.
7. Input interface- micro USB.
8. Work temperature- -10 to +85.
9. Inversed polarity- NO.
10.Size- small about 26mm x 17mm
With MICRO USB female socket can be connect with mobile phone charger directly for charging lithium battery.
Input Voltage5V, Cut-off charging voltage 4.2V +/- 1%
Maximum charging current 1000mA
Battery over-discharge protection voltage 2.5V
Battery over-discharge protection current 3A
NOTE:
1. Ampere meter can only be connected to 5v input end of the module.
2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to chip.
6. NO Reveral polarity.
SKU: ARD25
IOT & ESP8266
ESP32 ESP-32 ESP-32S DEVELOPMENT BOARD WIFI BLUETOOTH IOT
Features:
=================================
– High performance-price ratio;
– Small volume,easily embeded to other products;
– Strong function with support LWIP protocol,Freertos;
– Suppporting three modes: AP, STA, and AP+STA;
– Supporting Lua program, easily to develop.
Spesifikasi:
=================================
– Operating voltage : 3.3V
– Input voltage : 7-12V (Vin)
– Digital IO Pin (DIO) : 25
– Analog Input Pin (ADC) : 6
– Analog Output Pin (DAC) : 2
– UART : 3
– SPI : 2
– I2C : 3
– Flash Memory 4 MB
– SRAM : 520 KB
– Clock Speed : 240 Mhz
– Wi Fi : IEEE 802.11 b/g/n/e/i
– Mode supported : AP, STA, AP+STA
– CP2102 USB ccontroller
Aplikasi:
=================================
– IOT
– Smart lighting
– Wireless sensor networks
– Home automation
– Tele medicine
– Telemetri
– WiFi / Bluetooth Audio player
– WiFi camera
– MP3 decoding
– WiFi range extender
SKU: IOT11
IOT & ESP8266
CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32
Features:
– Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
– Low-power dual-core 32-bit CPU for application processors
– Up to 240MHz, up to 600 DMIPS
– Built-in 520 KB SRAM, external 4M PSRAM
– Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
– Support OV2640 and OV7670 cameras with built-in flash
– Support for images WiFI upload
-Support TF card
– Support multiple sleep modes
– Embedded Lwip and FreeRTOS
– Support STA/AP/STA+AP working mode
– Support Smart Config/AirKiss One-click distribution network
– Support for serial local upgrade and remote firmware upgrade (FOTA)
Note:
This product contains the OV2640 Camera Module. If you need to use the OV7670 camera, please purchase it separately.
Paket :
1 x CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32
SKU: IOT10
Power Amplifier
Power Amplifier Board TPA3116D2 XH-M548 Bluetooth
XH-M548 Bluetooth Dual Channel 120W+120W TPA3116D2 Digital Audio Power Amplifier Board Module
Specification:
Chip: TPA31 16D2
Power supply voltage: DC12 to 24V
Output power: 120W x 2
Power supply current: > 3A
Power ratio: >90%
Bluetooth module: BTM835/CRS8635 (4.0 edition)
Transmission distance: maximum 10m (no interference)
Channel number: 2 channel (high bass control)
Switching frequency: 1.2MHz
Support system: for Android IOS Windows
Size: 98 x 80 x 15mm/3.85 x 3.14 x 0.59”
Bluetooth connection method:
Take mobile phones as an example:
1. Turn on the Bluetooth.
2. Turn on “check all your devices around you”.
3. Click the search device “loudspeaker”, and connected.
4. The Bluetooth status indicator does not flicker alternately, turn on the player and listen to the music.
Isi paket :
1x Power Amplifier Board TPA3116D2 XH-M548 Bluetooth
SKU: AMP01
Programmer Modul
RASPBERRY PI CAMERA MODULE REV 1.3
Specification:
Sensor: Omnivision OV5647
Pixels Size: 5MP
Diagonal angle : 65 degree
Resolution: 2592 1944 still picture
Video Recording Support: 1080p30, 720p60 and 640x480p60/90
Compatibility: Raspberry Pi Standard Camera / CSI Port
Cable length: FFC 14 cm approx
Package Iist:
– 1 x Raspberry Pi Camera v1.3
– 1 x 14 cm FFC Flexible Cable
SKU: RAS03
Led
3 Digit LED Seven Segment 7 segmen 0.56″ inch Red Common Cathode Merah
Jumlah kaki : 12 pin
Tinggi angka : 0.56inch / 14.3mm
Ukuran display :
P : 37.5MM
L : 19mm
T: 8mm
Warna : Merah
Jumlah digit : 3 angka
Jenis Kolon : Titik
Jenis Segment : Common Cathode (Pin GND (-) jadi satu)
Tegangan Kerja : 2.8 – 5.0V DC (rekomendasi 2.8-3.3v kalau ke 5V bisa menggunakan R 100-220 Ohm. Tanpa Resistor berpotensi tidak tahan lama terutama bagian dot)
SKU: DISP05
Programmer Modul
RASPBERRY PI NOIR CAMERA MODULE V2 8MP PIXELS 1080P
Item description:
— NoIR camera,the Infrared night vision Camera V2
–800MP pixels, up to 3280 x 2464 pixels static image
–Support 1080p30, 720p60 and 640x480p60 / 90 camera shooting
–Latest Sony IMX219 sensor
Raspberry Pi Official Original NoIR Camera v2,The lastest IMX219 sensor,8 megapixel,The Infrared night vision Camera V2
Package Included:
Official Raspberry Pi Camera V2 Night Vision * 1
Note:(Raspberry Pi Board is not included)
SKU: RAS02
GSM & GPS
SIMCOM SIM800L V2.0 QUAD BAND GPRS GSM SMS MODULE 5V TTL ARDUINO PNP
Spesifikasi:
– TTL serial interface compatible with 3.3V and 5V Microcontrollers, compatible with arduino.
– This SIM800L module has a set of TTL level serial interface, a set of power supply interface.
– Besides, there are a set of antenna interface on this module.
– Network support: Quad-Band 850 / 900/ 1800 / 1900 MHz, it can transmit Voice, SMS and data information with low power
– VDD TTL UART interface The TTL UART serial interface, you can connect the MCU like 51MCU or ARM or MSP430 directly. The pin of VDD is used to match voltage of the TTL.
– Model: SIMCOM SIM800L
– Zunixe
– Work voltage: 3.7V to 5V
– Size: 40mm x 28mm x 3mm
– GPRS multi-slot class 12/10
– GPRS mobile station class B
– Compliant to GSM phase 2/2+
– Class 4 (2 W @ 850/900MHz)
– Class 1 (1 W @ 1800/1900MHz)
Note : Imei produk ini belum didaftarkan, imei harus didaftarkan dulu di kemenperin atau bea cukai. tutorialnya bisa dicari di youtube.
Kelengkapan:
1 set SIM800L GSM/GPRS Module sudah termasuk dengan antenna externalnya dan kabel coaxial dengan panjang sekitar 10cm
SKU: GSM07
GSM & GPS
SIM900 GSM GPRS QUAD BAND SHIELD MODULE FOR ARDUINO UNO MEGA
Features
Quad-Band 850 / 900/ 1800 / 1900 MHz – would work on GSM networks in all countries across the world.
GPRS multi-slot class 10/8
GPRS mobile station class B
Compliant to GSM phase 2/2+
Class 4 (2 W @ 850 / 900 MHz)
Class 1 (1 W @ 1800 / 1900MHz)
Control via AT commands – Standard Commands: GSM 07.07 & 07.05 |
Enhanced Commands: SIMCOM AT Commands.
Short Message Service – so that you can send small amounts of data over the network
(ASCII or raw hexadecimal).
Embedded TCP/UDP stack – allows you to upload data to a web server.
RTC supported.
Selectable serial port.
Speaker and Headphone jacks
Low power consumption – 1.5mA(sleep mode)
Industrial Temperature Range – -40°C to +85 °C
Size:8.5×5.7x2cm(approx)
Note : Imei produk ini belum didaftarkan, imei harus didaftarkan dulu di kemenperin atau bea cukai. tutorialnya bisa dicari di youtube.
SKU: GSM06
GSM & GPS
SIM808 GSM GPRS GPS MODULE BOARD ARDUINO RASPBERRY + ANTENNA
Spesifikasi:
– Quad-band 850/900/1800/1900MHz
– GPRS multi-slot class12
– connectivity: max. 85.6kbps(down-load/up-load)
– GPRS mobile station class B
– Controlled by AT Command (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT –
Commands)
– Supports Real Time Clock
– Supply voltage range 5V ~ 12V
– Integrated GPS/CNSS and supports A-GPS
– Supports 3.0V to 5.0V logic level
– Low power consumption, 1mA in sleep mode
– Supports GPS NMEA protocol
– Standard Micro SIM Card
Note : Imei produk ini belum didaftarkan, imei harus didaftarkan dulu di kemenperin atau bea cukai. tutorialnya bisa dicari di youtube.
Paket:
– 1x SIM808 GSM GPRS GPS MODULE BOARD ARDUINO RASPBERRY + ANTENNA
Terima kasih sudah mengunjungi halaman produk kami.
SKU: GSM03
Week Deals limited, Just now
%
Hurry up! Offer ends in:
Programmer Modul
MICRO USB 5V 1A 18650 TP4056 LITHIUM BATTERY CHARGER MODULE CHARGING
1. Charge module- Linear charging.
2. Current- 1A adjustable.
3. Charge precision- 1.5%.
4. Input voltage- 4.5V-5.5V.
5. Full charge voltage- 4.2V.
6. Led indicator- red is charging Green is full charged.
7. Input interface- micro USB.
8. Work temperature- -10 to +85.
9. Inversed polarity- NO.
10.Size- small about 26mm x 17mm
With MICRO USB female socket can be connect with mobile phone charger directly for charging lithium battery.
Input Voltage5V, Cut-off charging voltage 4.2V +/- 1%
Maximum charging current 1000mA
Battery over-discharge protection voltage 2.5V
Battery over-discharge protection current 3A
NOTE:
1. Ampere meter can only be connected to 5v input end of the module.
2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to chip.
6. NO Reveral polarity.
SKU: ARD25
IOT & ESP8266
ESP32 ESP-32 ESP-32S DEVELOPMENT BOARD WIFI BLUETOOTH IOT
Features:
=================================
– High performance-price ratio;
– Small volume,easily embeded to other products;
– Strong function with support LWIP protocol,Freertos;
– Suppporting three modes: AP, STA, and AP+STA;
– Supporting Lua program, easily to develop.
Spesifikasi:
=================================
– Operating voltage : 3.3V
– Input voltage : 7-12V (Vin)
– Digital IO Pin (DIO) : 25
– Analog Input Pin (ADC) : 6
– Analog Output Pin (DAC) : 2
– UART : 3
– SPI : 2
– I2C : 3
– Flash Memory 4 MB
– SRAM : 520 KB
– Clock Speed : 240 Mhz
– Wi Fi : IEEE 802.11 b/g/n/e/i
– Mode supported : AP, STA, AP+STA
– CP2102 USB ccontroller
Aplikasi:
=================================
– IOT
– Smart lighting
– Wireless sensor networks
– Home automation
– Tele medicine
– Telemetri
– WiFi / Bluetooth Audio player
– WiFi camera
– MP3 decoding
– WiFi range extender
SKU: IOT11
IOT & ESP8266
CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32
Features:
– Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
– Low-power dual-core 32-bit CPU for application processors
– Up to 240MHz, up to 600 DMIPS
– Built-in 520 KB SRAM, external 4M PSRAM
– Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
– Support OV2640 and OV7670 cameras with built-in flash
– Support for images WiFI upload
-Support TF card
– Support multiple sleep modes
– Embedded Lwip and FreeRTOS
– Support STA/AP/STA+AP working mode
– Support Smart Config/AirKiss One-click distribution network
– Support for serial local upgrade and remote firmware upgrade (FOTA)
Note:
This product contains the OV2640 Camera Module. If you need to use the OV7670 camera, please purchase it separately.
Paket :
1 x CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32
SKU: IOT10
Power Amplifier
Power Amplifier Board TPA3116D2 XH-M548 Bluetooth
XH-M548 Bluetooth Dual Channel 120W+120W TPA3116D2 Digital Audio Power Amplifier Board Module
Specification:
Chip: TPA31 16D2
Power supply voltage: DC12 to 24V
Output power: 120W x 2
Power supply current: > 3A
Power ratio: >90%
Bluetooth module: BTM835/CRS8635 (4.0 edition)
Transmission distance: maximum 10m (no interference)
Channel number: 2 channel (high bass control)
Switching frequency: 1.2MHz
Support system: for Android IOS Windows
Size: 98 x 80 x 15mm/3.85 x 3.14 x 0.59”
Bluetooth connection method:
Take mobile phones as an example:
1. Turn on the Bluetooth.
2. Turn on “check all your devices around you”.
3. Click the search device “loudspeaker”, and connected.
4. The Bluetooth status indicator does not flicker alternately, turn on the player and listen to the music.
Isi paket :
1x Power Amplifier Board TPA3116D2 XH-M548 Bluetooth
SKU: AMP01
Programmer Modul
RASPBERRY PI CAMERA MODULE REV 1.3
Specification:
Sensor: Omnivision OV5647
Pixels Size: 5MP
Diagonal angle : 65 degree
Resolution: 2592 1944 still picture
Video Recording Support: 1080p30, 720p60 and 640x480p60/90
Compatibility: Raspberry Pi Standard Camera / CSI Port
Cable length: FFC 14 cm approx
Package Iist:
– 1 x Raspberry Pi Camera v1.3
– 1 x 14 cm FFC Flexible Cable
SKU: RAS03
Led
3 Digit LED Seven Segment 7 segmen 0.56″ inch Red Common Cathode Merah
Jumlah kaki : 12 pin
Tinggi angka : 0.56inch / 14.3mm
Ukuran display :
P : 37.5MM
L : 19mm
T: 8mm
Warna : Merah
Jumlah digit : 3 angka
Jenis Kolon : Titik
Jenis Segment : Common Cathode (Pin GND (-) jadi satu)
Tegangan Kerja : 2.8 – 5.0V DC (rekomendasi 2.8-3.3v kalau ke 5V bisa menggunakan R 100-220 Ohm. Tanpa Resistor berpotensi tidak tahan lama terutama bagian dot)
SKU: DISP05
Programmer Modul
RASPBERRY PI NOIR CAMERA MODULE V2 8MP PIXELS 1080P
Item description:
— NoIR camera,the Infrared night vision Camera V2
–800MP pixels, up to 3280 x 2464 pixels static image
–Support 1080p30, 720p60 and 640x480p60 / 90 camera shooting
–Latest Sony IMX219 sensor
Raspberry Pi Official Original NoIR Camera v2,The lastest IMX219 sensor,8 megapixel,The Infrared night vision Camera V2
Package Included:
Official Raspberry Pi Camera V2 Night Vision * 1
Note:(Raspberry Pi Board is not included)
SKU: RAS02
GSM & GPS
SIMCOM SIM800L V2.0 QUAD BAND GPRS GSM SMS MODULE 5V TTL ARDUINO PNP
Spesifikasi:
– TTL serial interface compatible with 3.3V and 5V Microcontrollers, compatible with arduino.
– This SIM800L module has a set of TTL level serial interface, a set of power supply interface.
– Besides, there are a set of antenna interface on this module.
– Network support: Quad-Band 850 / 900/ 1800 / 1900 MHz, it can transmit Voice, SMS and data information with low power
– VDD TTL UART interface The TTL UART serial interface, you can connect the MCU like 51MCU or ARM or MSP430 directly. The pin of VDD is used to match voltage of the TTL.
– Model: SIMCOM SIM800L
– Zunixe
– Work voltage: 3.7V to 5V
– Size: 40mm x 28mm x 3mm
– GPRS multi-slot class 12/10
– GPRS mobile station class B
– Compliant to GSM phase 2/2+
– Class 4 (2 W @ 850/900MHz)
– Class 1 (1 W @ 1800/1900MHz)
Note : Imei produk ini belum didaftarkan, imei harus didaftarkan dulu di kemenperin atau bea cukai. tutorialnya bisa dicari di youtube.
Kelengkapan:
1 set SIM800L GSM/GPRS Module sudah termasuk dengan antenna externalnya dan kabel coaxial dengan panjang sekitar 10cm
SKU: GSM07
GSM & GPS
SIM900 GSM GPRS QUAD BAND SHIELD MODULE FOR ARDUINO UNO MEGA
Features
Quad-Band 850 / 900/ 1800 / 1900 MHz – would work on GSM networks in all countries across the world.
GPRS multi-slot class 10/8
GPRS mobile station class B
Compliant to GSM phase 2/2+
Class 4 (2 W @ 850 / 900 MHz)
Class 1 (1 W @ 1800 / 1900MHz)
Control via AT commands – Standard Commands: GSM 07.07 & 07.05 |
Enhanced Commands: SIMCOM AT Commands.
Short Message Service – so that you can send small amounts of data over the network
(ASCII or raw hexadecimal).
Embedded TCP/UDP stack – allows you to upload data to a web server.
RTC supported.
Selectable serial port.
Speaker and Headphone jacks
Low power consumption – 1.5mA(sleep mode)
Industrial Temperature Range – -40°C to +85 °C
Size:8.5×5.7x2cm(approx)
Note : Imei produk ini belum didaftarkan, imei harus didaftarkan dulu di kemenperin atau bea cukai. tutorialnya bisa dicari di youtube.
SKU: GSM06
GSM & GPS
SIM808 GSM GPRS GPS MODULE BOARD ARDUINO RASPBERRY + ANTENNA
Spesifikasi:
– Quad-band 850/900/1800/1900MHz
– GPRS multi-slot class12
– connectivity: max. 85.6kbps(down-load/up-load)
– GPRS mobile station class B
– Controlled by AT Command (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT –
Commands)
– Supports Real Time Clock
– Supply voltage range 5V ~ 12V
– Integrated GPS/CNSS and supports A-GPS
– Supports 3.0V to 5.0V logic level
– Low power consumption, 1mA in sleep mode
– Supports GPS NMEA protocol
– Standard Micro SIM Card
Note : Imei produk ini belum didaftarkan, imei harus didaftarkan dulu di kemenperin atau bea cukai. tutorialnya bisa dicari di youtube.
Paket:
– 1x SIM808 GSM GPRS GPS MODULE BOARD ARDUINO RASPBERRY + ANTENNA
Terima kasih sudah mengunjungi halaman produk kami.
SKU: GSM03
Smartphones & Tablets
- Programmer Modul
MICRO USB 5V 1A 18650 TP4056 LITHIUM BATTERY CHARGER MODULE CHARGING
1. Charge module- Linear charging.
2. Current- 1A adjustable.
3. Charge precision- 1.5%.
4. Input voltage- 4.5V-5.5V.
5. Full charge voltage- 4.2V.
6. Led indicator- red is charging Green is full charged.
7. Input interface- micro USB.
8. Work temperature- -10 to +85.
9. Inversed polarity- NO.
10.Size- small about 26mm x 17mmWith MICRO USB female socket can be connect with mobile phone charger directly for charging lithium battery.
Input Voltage5V, Cut-off charging voltage 4.2V +/- 1%
Maximum charging current 1000mA
Battery over-discharge protection voltage 2.5V
Battery over-discharge protection current 3ANOTE:
1. Ampere meter can only be connected to 5v input end of the module.
2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to chip.
6. NO Reveral polarity.SKU: ARD25 - IOT & ESP8266
ESP32 ESP-32 ESP-32S DEVELOPMENT BOARD WIFI BLUETOOTH IOT
Features:
=================================
– High performance-price ratio;
– Small volume,easily embeded to other products;
– Strong function with support LWIP protocol,Freertos;
– Suppporting three modes: AP, STA, and AP+STA;
– Supporting Lua program, easily to develop.Spesifikasi:
=================================
– Operating voltage : 3.3V
– Input voltage : 7-12V (Vin)
– Digital IO Pin (DIO) : 25
– Analog Input Pin (ADC) : 6
– Analog Output Pin (DAC) : 2
– UART : 3
– SPI : 2
– I2C : 3
– Flash Memory 4 MB
– SRAM : 520 KB
– Clock Speed : 240 Mhz
– Wi Fi : IEEE 802.11 b/g/n/e/i
– Mode supported : AP, STA, AP+STA
– CP2102 USB ccontrollerAplikasi:
=================================
– IOT
– Smart lighting
– Wireless sensor networks
– Home automation
– Tele medicine
– Telemetri
– WiFi / Bluetooth Audio player
– WiFi camera
– MP3 decoding
– WiFi range extenderSKU: IOT11 - IOT & ESP8266
CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32
Features:
– Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
– Low-power dual-core 32-bit CPU for application processors
– Up to 240MHz, up to 600 DMIPS
– Built-in 520 KB SRAM, external 4M PSRAM
– Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
– Support OV2640 and OV7670 cameras with built-in flash
– Support for images WiFI upload
-Support TF card
– Support multiple sleep modes
– Embedded Lwip and FreeRTOS
– Support STA/AP/STA+AP working mode
– Support Smart Config/AirKiss One-click distribution network
– Support for serial local upgrade and remote firmware upgrade (FOTA)Note:
This product contains the OV2640 Camera Module. If you need to use the OV7670 camera, please purchase it separately.
Paket :
1 x CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32SKU: IOT10 - Power Amplifier
Power Amplifier Board TPA3116D2 XH-M548 Bluetooth
XH-M548 Bluetooth Dual Channel 120W+120W TPA3116D2 Digital Audio Power Amplifier Board Module
Specification:
Chip: TPA31 16D2
Power supply voltage: DC12 to 24V
Output power: 120W x 2
Power supply current: > 3A
Power ratio: >90%
Bluetooth module: BTM835/CRS8635 (4.0 edition)
Transmission distance: maximum 10m (no interference)
Channel number: 2 channel (high bass control)
Switching frequency: 1.2MHz
Support system: for Android IOS Windows
Size: 98 x 80 x 15mm/3.85 x 3.14 x 0.59”Bluetooth connection method:
Take mobile phones as an example:
1. Turn on the Bluetooth.
2. Turn on “check all your devices around you”.
3. Click the search device “loudspeaker”, and connected.
4. The Bluetooth status indicator does not flicker alternately, turn on the player and listen to the music.Isi paket :
1x Power Amplifier Board TPA3116D2 XH-M548 BluetoothSKU: AMP01
Music Headphones
- Programmer Modul
MICRO USB 5V 1A 18650 TP4056 LITHIUM BATTERY CHARGER MODULE CHARGING
1. Charge module- Linear charging.
2. Current- 1A adjustable.
3. Charge precision- 1.5%.
4. Input voltage- 4.5V-5.5V.
5. Full charge voltage- 4.2V.
6. Led indicator- red is charging Green is full charged.
7. Input interface- micro USB.
8. Work temperature- -10 to +85.
9. Inversed polarity- NO.
10.Size- small about 26mm x 17mmWith MICRO USB female socket can be connect with mobile phone charger directly for charging lithium battery.
Input Voltage5V, Cut-off charging voltage 4.2V +/- 1%
Maximum charging current 1000mA
Battery over-discharge protection voltage 2.5V
Battery over-discharge protection current 3ANOTE:
1. Ampere meter can only be connected to 5v input end of the module.
2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to chip.
6. NO Reveral polarity.SKU: ARD25 - IOT & ESP8266
ESP32 ESP-32 ESP-32S DEVELOPMENT BOARD WIFI BLUETOOTH IOT
Features:
=================================
– High performance-price ratio;
– Small volume,easily embeded to other products;
– Strong function with support LWIP protocol,Freertos;
– Suppporting three modes: AP, STA, and AP+STA;
– Supporting Lua program, easily to develop.Spesifikasi:
=================================
– Operating voltage : 3.3V
– Input voltage : 7-12V (Vin)
– Digital IO Pin (DIO) : 25
– Analog Input Pin (ADC) : 6
– Analog Output Pin (DAC) : 2
– UART : 3
– SPI : 2
– I2C : 3
– Flash Memory 4 MB
– SRAM : 520 KB
– Clock Speed : 240 Mhz
– Wi Fi : IEEE 802.11 b/g/n/e/i
– Mode supported : AP, STA, AP+STA
– CP2102 USB ccontrollerAplikasi:
=================================
– IOT
– Smart lighting
– Wireless sensor networks
– Home automation
– Tele medicine
– Telemetri
– WiFi / Bluetooth Audio player
– WiFi camera
– MP3 decoding
– WiFi range extenderSKU: IOT11 - IOT & ESP8266
CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32
Features:
– Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
– Low-power dual-core 32-bit CPU for application processors
– Up to 240MHz, up to 600 DMIPS
– Built-in 520 KB SRAM, external 4M PSRAM
– Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
– Support OV2640 and OV7670 cameras with built-in flash
– Support for images WiFI upload
-Support TF card
– Support multiple sleep modes
– Embedded Lwip and FreeRTOS
– Support STA/AP/STA+AP working mode
– Support Smart Config/AirKiss One-click distribution network
– Support for serial local upgrade and remote firmware upgrade (FOTA)Note:
This product contains the OV2640 Camera Module. If you need to use the OV7670 camera, please purchase it separately.
Paket :
1 x CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32SKU: IOT10 - Power Amplifier
Power Amplifier Board TPA3116D2 XH-M548 Bluetooth
XH-M548 Bluetooth Dual Channel 120W+120W TPA3116D2 Digital Audio Power Amplifier Board Module
Specification:
Chip: TPA31 16D2
Power supply voltage: DC12 to 24V
Output power: 120W x 2
Power supply current: > 3A
Power ratio: >90%
Bluetooth module: BTM835/CRS8635 (4.0 edition)
Transmission distance: maximum 10m (no interference)
Channel number: 2 channel (high bass control)
Switching frequency: 1.2MHz
Support system: for Android IOS Windows
Size: 98 x 80 x 15mm/3.85 x 3.14 x 0.59”Bluetooth connection method:
Take mobile phones as an example:
1. Turn on the Bluetooth.
2. Turn on “check all your devices around you”.
3. Click the search device “loudspeaker”, and connected.
4. The Bluetooth status indicator does not flicker alternately, turn on the player and listen to the music.Isi paket :
1x Power Amplifier Board TPA3116D2 XH-M548 BluetoothSKU: AMP01
Top Categories this Week
Laptops & Computers
Programmer ModulUNO R3 SMD CH340 ATMEGA328P PLUS KABEL USB DAN PIN HEADER
Spesifikasi :
– Microcontroller : ATmega328 SMD
– Operating Voltage : 5V
– Input Voltage (recommended) : 7-12V
– Digital I/O Pins : 14 (of which 6 provide PWM output)
– Analog Input Pins : 6
– Flash Memory : 32 KB (ATmega328) of which 0.5 KB used by bootloader
– SRAM : 2 KB (ATmega328)
– EEPROM : 1 KB (ATmega328)
– Clock Speed : 16 MHzSKU: ARD02
- Programmer Modul
MICRO USB 5V 1A 18650 TP4056 LITHIUM BATTERY CHARGER MODULE CHARGING
1. Charge module- Linear charging.
2. Current- 1A adjustable.
3. Charge precision- 1.5%.
4. Input voltage- 4.5V-5.5V.
5. Full charge voltage- 4.2V.
6. Led indicator- red is charging Green is full charged.
7. Input interface- micro USB.
8. Work temperature- -10 to +85.
9. Inversed polarity- NO.
10.Size- small about 26mm x 17mmWith MICRO USB female socket can be connect with mobile phone charger directly for charging lithium battery.
Input Voltage5V, Cut-off charging voltage 4.2V +/- 1%
Maximum charging current 1000mA
Battery over-discharge protection voltage 2.5V
Battery over-discharge protection current 3ANOTE:
1. Ampere meter can only be connected to 5v input end of the module.
2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to chip.
6. NO Reveral polarity.SKU: ARD25 - IOT & ESP8266
ESP32 ESP-32 ESP-32S DEVELOPMENT BOARD WIFI BLUETOOTH IOT
Features:
=================================
– High performance-price ratio;
– Small volume,easily embeded to other products;
– Strong function with support LWIP protocol,Freertos;
– Suppporting three modes: AP, STA, and AP+STA;
– Supporting Lua program, easily to develop.Spesifikasi:
=================================
– Operating voltage : 3.3V
– Input voltage : 7-12V (Vin)
– Digital IO Pin (DIO) : 25
– Analog Input Pin (ADC) : 6
– Analog Output Pin (DAC) : 2
– UART : 3
– SPI : 2
– I2C : 3
– Flash Memory 4 MB
– SRAM : 520 KB
– Clock Speed : 240 Mhz
– Wi Fi : IEEE 802.11 b/g/n/e/i
– Mode supported : AP, STA, AP+STA
– CP2102 USB ccontrollerAplikasi:
=================================
– IOT
– Smart lighting
– Wireless sensor networks
– Home automation
– Tele medicine
– Telemetri
– WiFi / Bluetooth Audio player
– WiFi camera
– MP3 decoding
– WiFi range extenderSKU: IOT11 - IOT & ESP8266
CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32
Features:
– Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
– Low-power dual-core 32-bit CPU for application processors
– Up to 240MHz, up to 600 DMIPS
– Built-in 520 KB SRAM, external 4M PSRAM
– Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
– Support OV2640 and OV7670 cameras with built-in flash
– Support for images WiFI upload
-Support TF card
– Support multiple sleep modes
– Embedded Lwip and FreeRTOS
– Support STA/AP/STA+AP working mode
– Support Smart Config/AirKiss One-click distribution network
– Support for serial local upgrade and remote firmware upgrade (FOTA)Note:
This product contains the OV2640 Camera Module. If you need to use the OV7670 camera, please purchase it separately.
Paket :
1 x CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32SKU: IOT10 - Power Amplifier
Power Amplifier Board TPA3116D2 XH-M548 Bluetooth
XH-M548 Bluetooth Dual Channel 120W+120W TPA3116D2 Digital Audio Power Amplifier Board Module
Specification:
Chip: TPA31 16D2
Power supply voltage: DC12 to 24V
Output power: 120W x 2
Power supply current: > 3A
Power ratio: >90%
Bluetooth module: BTM835/CRS8635 (4.0 edition)
Transmission distance: maximum 10m (no interference)
Channel number: 2 channel (high bass control)
Switching frequency: 1.2MHz
Support system: for Android IOS Windows
Size: 98 x 80 x 15mm/3.85 x 3.14 x 0.59”Bluetooth connection method:
Take mobile phones as an example:
1. Turn on the Bluetooth.
2. Turn on “check all your devices around you”.
3. Click the search device “loudspeaker”, and connected.
4. The Bluetooth status indicator does not flicker alternately, turn on the player and listen to the music.Isi paket :
1x Power Amplifier Board TPA3116D2 XH-M548 BluetoothSKU: AMP01 - Programmer Modul
RASPBERRY PI CAMERA MODULE REV 1.3
Specification:
Sensor: Omnivision OV5647
Pixels Size: 5MP
Diagonal angle : 65 degree
Resolution: 2592 1944 still picture
Video Recording Support: 1080p30, 720p60 and 640x480p60/90
Compatibility: Raspberry Pi Standard Camera / CSI Port
Cable length: FFC 14 cm approxPackage Iist:
– 1 x Raspberry Pi Camera v1.3
– 1 x 14 cm FFC Flexible CableSKU: RAS03 - Led
3 Digit LED Seven Segment 7 segmen 0.56″ inch Red Common Cathode Merah
Jumlah kaki : 12 pinTinggi angka : 0.56inch / 14.3mmUkuran display :P : 37.5MML : 19mmT: 8mmWarna : MerahJumlah digit : 3 angkaJenis Kolon : TitikJenis Segment : Common Cathode (Pin GND (-) jadi satu)Tegangan Kerja : 2.8 – 5.0V DC (rekomendasi 2.8-3.3v kalau ke 5V bisa menggunakan R 100-220 Ohm. Tanpa Resistor berpotensi tidak tahan lama terutama bagian dot)SKU: DISP05
Home Enternteinment
- Programmer Modul
UNO R3 SMD CH340 ATMEGA328P PLUS KABEL USB DAN PIN HEADER
Spesifikasi :
– Microcontroller : ATmega328 SMD
– Operating Voltage : 5V
– Input Voltage (recommended) : 7-12V
– Digital I/O Pins : 14 (of which 6 provide PWM output)
– Analog Input Pins : 6
– Flash Memory : 32 KB (ATmega328) of which 0.5 KB used by bootloader
– SRAM : 2 KB (ATmega328)
– EEPROM : 1 KB (ATmega328)
– Clock Speed : 16 MHzSKU: ARD02
- Programmer Modul
MICRO USB 5V 1A 18650 TP4056 LITHIUM BATTERY CHARGER MODULE CHARGING
1. Charge module- Linear charging.
2. Current- 1A adjustable.
3. Charge precision- 1.5%.
4. Input voltage- 4.5V-5.5V.
5. Full charge voltage- 4.2V.
6. Led indicator- red is charging Green is full charged.
7. Input interface- micro USB.
8. Work temperature- -10 to +85.
9. Inversed polarity- NO.
10.Size- small about 26mm x 17mmWith MICRO USB female socket can be connect with mobile phone charger directly for charging lithium battery.
Input Voltage5V, Cut-off charging voltage 4.2V +/- 1%
Maximum charging current 1000mA
Battery over-discharge protection voltage 2.5V
Battery over-discharge protection current 3ANOTE:
1. Ampere meter can only be connected to 5v input end of the module.
2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to chip.
6. NO Reveral polarity.SKU: ARD25 - IOT & ESP8266
ESP32 ESP-32 ESP-32S DEVELOPMENT BOARD WIFI BLUETOOTH IOT
Features:
=================================
– High performance-price ratio;
– Small volume,easily embeded to other products;
– Strong function with support LWIP protocol,Freertos;
– Suppporting three modes: AP, STA, and AP+STA;
– Supporting Lua program, easily to develop.Spesifikasi:
=================================
– Operating voltage : 3.3V
– Input voltage : 7-12V (Vin)
– Digital IO Pin (DIO) : 25
– Analog Input Pin (ADC) : 6
– Analog Output Pin (DAC) : 2
– UART : 3
– SPI : 2
– I2C : 3
– Flash Memory 4 MB
– SRAM : 520 KB
– Clock Speed : 240 Mhz
– Wi Fi : IEEE 802.11 b/g/n/e/i
– Mode supported : AP, STA, AP+STA
– CP2102 USB ccontrollerAplikasi:
=================================
– IOT
– Smart lighting
– Wireless sensor networks
– Home automation
– Tele medicine
– Telemetri
– WiFi / Bluetooth Audio player
– WiFi camera
– MP3 decoding
– WiFi range extenderSKU: IOT11 - IOT & ESP8266
CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32
Features:
– Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
– Low-power dual-core 32-bit CPU for application processors
– Up to 240MHz, up to 600 DMIPS
– Built-in 520 KB SRAM, external 4M PSRAM
– Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
– Support OV2640 and OV7670 cameras with built-in flash
– Support for images WiFI upload
-Support TF card
– Support multiple sleep modes
– Embedded Lwip and FreeRTOS
– Support STA/AP/STA+AP working mode
– Support Smart Config/AirKiss One-click distribution network
– Support for serial local upgrade and remote firmware upgrade (FOTA)Note:
This product contains the OV2640 Camera Module. If you need to use the OV7670 camera, please purchase it separately.
Paket :
1 x CAMERA OV2640 WIFI MODULE ESP32-CAM ESP-32SKU: IOT10 - Power Amplifier
Power Amplifier Board TPA3116D2 XH-M548 Bluetooth
XH-M548 Bluetooth Dual Channel 120W+120W TPA3116D2 Digital Audio Power Amplifier Board Module
Specification:
Chip: TPA31 16D2
Power supply voltage: DC12 to 24V
Output power: 120W x 2
Power supply current: > 3A
Power ratio: >90%
Bluetooth module: BTM835/CRS8635 (4.0 edition)
Transmission distance: maximum 10m (no interference)
Channel number: 2 channel (high bass control)
Switching frequency: 1.2MHz
Support system: for Android IOS Windows
Size: 98 x 80 x 15mm/3.85 x 3.14 x 0.59”Bluetooth connection method:
Take mobile phones as an example:
1. Turn on the Bluetooth.
2. Turn on “check all your devices around you”.
3. Click the search device “loudspeaker”, and connected.
4. The Bluetooth status indicator does not flicker alternately, turn on the player and listen to the music.Isi paket :
1x Power Amplifier Board TPA3116D2 XH-M548 BluetoothSKU: AMP01 - Programmer Modul
RASPBERRY PI CAMERA MODULE REV 1.3
Specification:
Sensor: Omnivision OV5647
Pixels Size: 5MP
Diagonal angle : 65 degree
Resolution: 2592 1944 still picture
Video Recording Support: 1080p30, 720p60 and 640x480p60/90
Compatibility: Raspberry Pi Standard Camera / CSI Port
Cable length: FFC 14 cm approxPackage Iist:
– 1 x Raspberry Pi Camera v1.3
– 1 x 14 cm FFC Flexible CableSKU: RAS03 - Led
3 Digit LED Seven Segment 7 segmen 0.56″ inch Red Common Cathode Merah
Jumlah kaki : 12 pinTinggi angka : 0.56inch / 14.3mmUkuran display :P : 37.5MML : 19mmT: 8mmWarna : MerahJumlah digit : 3 angkaJenis Kolon : TitikJenis Segment : Common Cathode (Pin GND (-) jadi satu)Tegangan Kerja : 2.8 – 5.0V DC (rekomendasi 2.8-3.3v kalau ke 5V bisa menggunakan R 100-220 Ohm. Tanpa Resistor berpotensi tidak tahan lama terutama bagian dot)SKU: DISP05